Free Shipping in Canada For Orders over $200-------------Save 5-35% On Nozzles Even Mix & Match ---------- Free Shipping to Continental USA On orders over $500 (some restrictions apply)
Reach Out to the Nozzle Ninja
Welcome to Nozzle Ninja!
1/2" PTC Stem Elbow is Available to direct rinse flow away from boom.
Fits all 1 inch boom lines with 10mm port size for nozzle body stems which is industry standard.
Conventional boom designs trap air in the boom causing a delay from the close signal to when spray actually stops. Pentair's Hypro Express nozzle body end caps include a passive fe...
This Valve replaces the cap in an existing express end to quickly flush the boom section without using tools.
-Compact valve design limits the length it extendsbeyond the last nozzle body to fit most boom structures-Chemically-resistant, stainless steel ball and viton o-rings extending life-Handle includes standard wrench square head slot to ope...
Retrofit to replace plug in express end cap with robust ball valve with 1/2" PTC port for easy cleaning and maintenance.
1/2" PTC Stem elbow is available to keep rinsate off of the boom
Express End Cap with flush valve benefits
- Eliminates trapped air from the boom by allowing air to escape through the nozzle body, reducing nozzle turn-off tim...
Does Not Include 17mm High Flow Nozzle Body or 1/2" Stem Elbow
Fits all 1 inch boom lines with 17mm port size for nozzle body stems which are typically found on John Deere Factory Stainless Steel Boom Lines.
Conventional boom designs trap air in the boom causing a delay from the close signal to when spray actually stops. Pentair's Hypro Express ...
Fitting Push to Connect
Use with Express Flush Valve Assembly Or Express Retrofit Valve to direct clean out flow away from the boom to the ground or to add a circuit to recirculate contaminants back to the solution tank. Connect and disconnect tubing without tools. Meets FDA standards & NSF listed. O-ring/collet design. Body is polypropylene, O-rings are EPDM. Coll...
This kit will work with 1" boom lines that have male 1" NPT threads. Also included in the kit is two 3/4 inch male to 1" male adapters to allow the valves to be installed on the centre boom section of John Deere 4700's to 4830's.
Why Should This Be Put On My Sprayer?
Most carryover damage and clean out problems can be traced to product that gets...
Use this microvalve to provide a quick flush port for 1.5", 2" Banjo line strainers with a 1" fpt port in the Strainer bowl.
3/4" mpt by 3/4" Hose Barb Micro Valve, This will work as a flush valve for 3" Banjo Strainers or strainers with a 3/4" plug in the bowl
1/2"mpt by 3/8" hose barb Microvalve, can be used as a flush valve for banjo 3/4 and 1 inch strainers or any strainer with a 1/2"fpt threaded port in the bowl
The SF-1100 Series Bulk Chemical Pumps are the industry leader. They are designed for efficiency and power to handle highly viscous fluids.
Servicing the SF-1100 series pump is a rare event, but if needed, it can be serviced quickly and easily with only a few hand tools.
Specialized EPDM elastics
12 volt DC or 110 volt AC motor option
20 foot c...
Includes T6F to 2" Standard Port Flange Connections (qty2) and 3 Metre Power Cable (10ft)
Available with Pump Stop version for automatic tank filling command
Selectable value for the fluid amount to be filled into the tank
Power supply: 12 Vdc
0-12 Vdc pulse output with frequency proportional to rate
Includes 2" standard Port Manifold Flange Fittings (qty2)
2 cells AA (LR6)
Automatic switching on/off
Programmable multilingual graphic display
Available either with external battery (12 Vdc) or inside cell power supply
Display snap-on cover
Body with fork connectors for flexible ...
Also Available without display
See Spec sheet attached for Flow and pressure Specifications
Electro-magnetic flow meter
Ships with 1.5" Male Camlock Adaptors and 3 metre/10ft Cable
Advantages• No mechanical moving parts inside the pipe• Performances independent from fluid density and viscosity• Low sensitivity to turbulence• High precision• Low ...
1.5" Flow Meter Kit features a a 1.5" Orion Flow Meter and a 1.5" Wolf Paddle Wheel Flow meter. These two flow meters connect to a single Visio display. The Visio then can provide an instant, batch, and total flow rate for each meter. The Visio can also be used as a switch to operate a shutoff valve or an ignition switch on a pump with the inclu...
Use this water Sensitive paper to get a visual confirmation of the spray quality to test different configurations to get the most out of your investment in application technologies
Systems and Controls
Accurate to between 0.25% to 0.5% of maximum tank capacity.
Includes all cables for installation-Sensor uses 0.25 inch Male Threads
Please call for installation options for different makes and models.
-Visio Display with mounting Clip (Suction Cup Mount Not Included)
-Dual Sensor Cable
-Tank Level Sensor
The Accu-Volume System puts the “Precision” in spraying by accurately measuring and displaying a “live, real time” amount of every gallon of solution within the sprayer’s tank(s). With Digital Displays being mounted, one inside the cab and another at the load station. This will give the operator a live display while filling and spraying product...
The Nozzle Ninja's Take:Guardian Air (GA)/Low Drift Air (LDA)
The Guardian Air is a proven performer. An excellent combination of coverage and drift control. if you are looking for one nozzle that can do it all and provide consistent operation in a wide pressure window the Guardian Air or as some Deere people may call it the LDA Low drift Air is...
Nozzle Ninja's Take on the Guardian Air Twin (GAT)
Take the qualities of the Guardian Air and combine it into a one piece design with dual outlets spraying 20 degrees forward and back. That is the GAT. The revised housing is durable and does not fall apart like earlier versions of the GAT and allows for the use of a twin spray nozzle without the...
The original guardian is a one piece design for ISO Hypro/TeeJet square lug nozzle bodies but can be adapted to a Wilger nozzle body with an adaptor. The Guardian has a 20 degree spray angle and produces a VC to M droplet dependent on pressure. The nozzles can be alternated forward and backward to improve vertical target coverage...
If you like the performance and droplet profile of the Ultra low drift (ULD)but were concerned with two smaller orifices of the ULD Plugging then the Air Stubble Jet nozzle will be right in your wheel house. For those of you that are a fan of the Guardian Air but would like something that maintains a coarse droplet into higher pressures the Air ...
If you are looking for an air induction nozzle that will keep your crop protection products on target, is resistant to plugging, and will leave a few extra dollars in your pocket have a look at the Compact Fan Air. The CFA produces Coarse to Very Coarse droplets at operating pressures of 35-100 psi. The large air filled droplets burst upon impac...
If you are looking for an air induction nozzle that will provide wider application windows and peace of mind in drift sensitive areas the CFAU is a solid performer. The CFAU is designed to run at higher pressures with 35 PSI the lowest recommended operating pressure without efficacy concerns. Optimal pressures are 50psi and up. The CFAU produces...
Nozzle Ninja's Take on the Ultra Low Drift (ULD)
Bread and Butter, Workhorse, Veteran Pro, these could all be used to describe the ULD. It is a tried, tested and true air induction nozzle that delivers exactly as advertised. Drift reduction and coverage.
The ULD performs best from 50psi to 80 psi but holds its pattern width well down to 25 psi.
Nozzle End Row
Produces an off centre air induction pattern of Coarse to Very Coarse Droplets. THis will minimize drift and unwanted over spray in fence row applications. Typical effective range is 3-7ft depending on boom height and operating pressure.
Uses Standard CAP00
Drift control up to 90%.
Compact design, simple replacement in flat fan nozzle body.
Non- Air Induction Design Suitable for PWM Systems at 30hz PWM operating below 30hz all nozzles should point in the same direction.
Designed in partnership with Syngenta using wind tunnel research and more than 10 years of agronomic field trials
Proven to deliver up to a 10% increase in pre-emerge weedcontrol compared to a conventional ...
The Low Drift Ceramic Nozzle from ASJ is PWM Compatible. It is a pre-orifice Ceramic nozzles that produces Coarse to Very Coarse droplets in the ISO 0.3gpm to 0.6gpm sizes making it a great choice for PWM and Exact Apply users looking for a coarser spray quality.
This nozzle is not as coarse as the ADI Ceramic but is generally coarser than the ...
The ESI six stream nozzle is designed for applying liquid fertilizer. It creates six individual streams that distribute the fertilizer on the soil while gettingless on the crop. The wear resistant metering orifice and unique low pressure distribution chamber keep the streams stable to reduce atomization andprevent leaf burn and scorching. Spacin...